1/8/2024 0 Comments Keymo mountI’ll update again when I’ve got some rounds through it, but I’m satisfied thus far. Simple, clean, and effective, the 6315 is an excellent option for your next AR-15 build. The impressive suppression capabilities combined with the lightweight and small design are proof that larger muzzle devices aren’t necessarily better. No rounds through it yet, but I assume it’ll perform as well as a normal A2, which on an AR should be more than adequate.Īll in all, it’s about half an inch shorter and 2.5-3oz lighter than keymo, and seems to be just as secure of a mount. Forward Controls Design Stoner 63 Style Compensator Dead Air Keymo Mount 1/2×28. The flash hider itself looks almost identical to an A2 at a glance, until you notice the outer threads on it. The left hand threads take some getting used to but it threads up consistently to the same spot on the taper and everything looks concentric looking through the receiver down the barrel. After running it all the way up with a wrench and back off a few times I’ve got it worn down enough to get threaded on by hand with a bit of clp on the threads. Whatever coating (nitride, I’m assuming) is on male threads on the adapter is a tad bit thick, making threading into the can by hand all but impossible the first few times. Dead Air themselves enveloped the HUB pattern with the release of the Nomad, and Griffin Armament did the same thing with the launch of the Bushwhacker 46 even including adapters for their own devices.Update for anyone who searches for this in the future I went ahead and picked up a xeno adapter and flash hider from my local shop. Ourselves we have some bi-lock to 1.375 adapters. However, I did not necessarily go through the whole routine of timing the brake, or. Everything seemed to be GTG with regards to mounting and removing the suppressor. The Dead Air Keymo system allows folks to break into the HUB 1.375×24 TPI space. So I've decided to replace my SiCo Trifecta muzzle devices and the MAAD mount on my Saker with the Dead Air Key-Mo system. Though we have yet to come across an adapter for Surefire muzzle devices, likely due to the complexity, we anticipate it happening in the aftermarket sometime in the future.Ĭompanies will well-established mounts like Surefire, Dead Air, and Gemtech probably can and will continue using their mounting systems while embracing the aftermarket. With a HUB 1.374×24, you'll never have that problem, even if the silencer company goes out of business the day after you buy a can. Unfortunately, neither the mount nor the silencers were entirely backward-compatible they aspired to make it work, but it was impossible with the new locking mechanism. Years back when Surefire released their SOCOM-series of suppressors they rolled out an improved mounting system. The current practice used by companies like Dead Air and Griffin Armament is to include a pair of wrenches to ensure everything stays in place, but we've still inadvertently rotated HUB 1.375×24 TPI silencers off of adapters regardless of what wrenches were used. The internal adapters are more tricky because if you want to keep the modular aspect of your silencer, thread locker is going to make it all the more difficult. The muzzle device is the easiest fix here, as all you have to do is use a little Rocksett during installation. This means when you're removing your silencer you can potentially rotate off your muzzle device, rotate the adapter out of the silencer, or remove the silencer as intended. As of right now, unless you're using an Area 419 adapter, everything is threaded right-hand. It's far too late in the game to make the change now, but we absolutely wish that SilencerCo changed the wheel a bit more and instead threaded this new module for a 1.375×24 *lefthand*. The HUB 1.375×24 pitch is a standard used for bicycle hubs and locks, so the wheel wasn't reinvented, but instead repurposed. There are more than a dozen companies making devices, adapters, boosters, and more for this pattern. People screaming for an easier-to-use mount helped kick the can along further. It has since been dubbed the HUB: Hybrid Universal Base. The Gemtech Multi-mount and ONE has a similar system, as does Liberty Suppressors with the Mystic and virtually any new release moving forward.Ī combination of the sheer numbers of SilencerCo mounts in existence along with the larger diameter of 1.375-mount silencers which makes it easier for mounts to fit ensured SilencerCo would be the winner. And SilencerCo wasn't the only one working towards a modular back-end. Police arrested Ronnie Dean Busick, 66, on Sunday in connection with the killings of Ashley Freeman and Lauria Bible, both 16, and Ashley’s parents Danny and Kathy Freeman in the now-abandoned town of Picher, Oklahoma.Though they probably didn't realize it at the time, when SilencerCo released the Hybrid line with a 1.375×24 internal thread, they would be making the universal standard what would relegate proprietary muzzle devices as a thing of the past.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |